본문 바로가기


Gas & Liquid Control Technology with DRASTAR

DRA300 (Springless)

UHP VCR Springless Single Stage Pressure Reducing Regulators

5ab4f2774603c.jpg

  Products Feature

UHP Low Pressure VCR Type(1/4" 3/8" 1/2" 3/4")

DRA300 Series is an Springless tied-diaphragm type UHP low pressure reducing regulator with surface finishes to B.A. 25Ra, E.P. 10Ra, or E.P. 5Ra microinch and applicable for gas cabinet for semiconductor manufacturing, specialty gases, valve manifold boxes, and research labs, etc. Inlet pressures are 3000psig (210bar) or 600psig (42bar) and outlet pressures are from 5psig (0.3bar) up to 250psig (17bar).

★ Springless type VCR regulator: By adopting the “flat- wave-shaped ring spring” (DRASTAR patent #10-1191514) instead of conventional spring, particle generation by spring itself due to fatigue from long-time use can be kept down
★ To use more suitably for corrosive gas applications, 316L or 316L VIM+VAR (double melt) available as optional
★ Tied-diaphragm design for positive shut-off and protecting the rupture of diaphragm
★ Surfaces finishes to B.A. 25Ra, E.P. 10 Ra or E.P. 5 Ra microinch
★ Push and lock type handle (DRASTAR patent #10-1086199) mounted
★ Threadless type: enhanced particle prevention by adopting the locking-plate seal system (DRASTAR patent #10-0753280)
★ All works of welding, assembly, test and cleaning are performed in class 100 and class 10 clean-rooms
★ Design proof pressure: 150% of maximum rated
★ Applicable for Semiconductor manufacturing gas line, toxic gases, pyrophoric gases, and high corrosive gases

※ With DRASTAR’s patented (patent #1086199) “push and lock type handle”, you can operate it easily and stably; “locking” by pushing down the handle will prevent any slight change of pre-set pressure value, which could possibly be caused by any vibration from gas pipeline or ambient applications and the other way “unlocking” by pulling it back enables you to adjust the pressure value freely again.

  Ordering Information.

DRA300 - 025 S - H
BASIS
SERIES
NUMBER
BODY MATERIAL &
SURFACE FINISH
OUTLET
PRESSURE
RANGE
DIAPHRAGM
MATERIAL
MAX.
INLET
PRESSURE


DRA300


A = 316L B.A -------------- 25Ra

B = 316L E.P -------------- 10Ra

C = 316L E.P(P.E.P) ------- 5Ra

D = 316L VAR E.P ---------- 10Ra

E = 316L VAR E.P(P.E.P)---- 5Ra  

 

025 = 1-25psi (.1-1.7bar) 

050 = 1-50psi (.1-3.5bar) 

100 = 1-100psi (.1-7bar) 

130 = 1-130psi (.2-9bar) 

150 = 1-150psi (.2-10.3bar) 

250 = 1-250psi (.2-17bar)

 

S = STS 316L

H = Hastelloy-C
H = 3000psi(210bar)

L = 600psi(42bar)
P S - 4MS - G0S
SEAT
MATERIAL
FLOW
CAPACITY
INLET
OUTLET
PORTS SIZE
                  Type "A" ± 1.0mm
GAUGE
PORTS
OPTIONS
               Gauge Ports
P = PCTFE

T = Teflon

V = Vespel
S = Cv 0.06
    1/4" Standard

O = Cv 0.2
    1/4" Optional

S = Cv 0.2
    3/8" Standard

S = Cv 0.5
    1/2" Standard

O = Cv 1.0
    1/2" Optional

S = Cv 1.2
    3/4" Standard

4HP = 1/4" H.P.I.C

4MS = 1/4" Male Swivel ---- 94mm
4FS = 1/4" Female Swivel -- 94mm
4FL = 1/4" Female Swivel -- 114mm
4ML = 1/4" Male Swivel ---- 114mm

8MS = 3/8" Male Swivel ---- 120mm
8FS = 3/8" Female Swivel -- 120mm

2MS = 1/2" Male Swivel ---- 140mm
2FS = 1/2" Female Swivel -- 140mm
2ML = 1/2" Male Swivel ---- 180mm
2FL = 1/2" Female Swivel -- 180mm

3MS = 3/4" Male Swivel ---- 160mm
3FS = 3/4" Female Swivel -- 160mm

4IMF = In 1/4" Male
           Out 1/4" Female ----- 94mm
4IFM = In 1/4" Female
          Out 1/4" Male ------- 94mm

2IMF = In 1/2" Male
          Out 1/2" Female ----- 140mm
2IFM = In 1/2" Female
          Out 1/2" Male ------- 140mm
2IMFL = In 1/2" Male
          Out 1/2" Female ----- 180mm
2IFML = In 1/2" Female
          Out 1/2" Male ------- 180mm

4TS = 1/4" Tube Stubs ---- 94mm
8TS = 3/8" Tube Stubs ---- 94mm
2TS = 1/2" Tube Stubs ---- 120mm

G0S = None ------------- 0

G1S = 1/4" H.P.I.C ------- 1

G2S = 1/4" H.P.I.C ------- 2

G2B = 1/4" H.P.I.C ------- 2

M1S = 1/4" Male Swivel -- 1

M2S = 1/4" Male Swivel -- 2

M2B = 1/4" Male Swivel -- 2

F1S = 1/4" Femle Swivel -- 1

F2S = 1/4" Femle Swivel -- 2

F2B = 1/4" Femle Swivel -- 2

  Specification

 Ports

  DRA300-A100S-xxx-4MS-GxS   1/4"  Male
  DRA300-A100S-xxx-4FS-GxS    1/4"  Female
  DRA300-A100S-xxx-8MS-GxS   3/8"  Male
  DRA300-A100S-xxx-8FS-GxS    3/8"  Female
  DRA300-A100S-xxx-2MS-GxS   1/2"  Male
  DRA300-A100S-xxx-2FS-GxS    1/2"  Female
  DRA300-A100S-xxx-3MS-GxS   3/4"  Male
  DRA300-A100S-xxx-3FS-GxS    3/4"  Female

 Design Pressure

  150% maximum rated

 Leak Rate
 Certification

  to 1 x 10 -9 atm cc/sec Helium available.

 Body Materials

  DRA300-A100x-xxx-xxS-GxS 316L B.A ------------------ 25Ra
  DRA300-B100x-xxx-xxS-GxS 316L E.P ------------------ 10Ra
  DRA300-C100x-xxx-xxS-GxS 316L E.P(P.E.P) ------------5Ra
  DRA300-D100x-xxx-xxS-GxS 316L VAR E.P ---------------10Ra
  DRA300-E100x-xxx-xxS-GxS 316L VAR(P.E.P) ------------ 5Ra

 Bonnet Material

  Nickel Plated Brass (Stainless steel 316L Optional)

 Diaphragm

  DRA300-x100S-xxx-xxS-GxS  STS 316L
  DRA300-x100H-xxx-xxS-GxS  Hastelloy-C22

 Main Valve

  DRA300-A100S-xxx-xxS-GxS  Stainless steel 316L  Standard
  DRA300-B100H-xxx-xxS-GxS  Hastelloy-C22  Optional

 Valve Spring


  Valve Seat

  DRA300-B100S-xPx-xxS-GxS  PCTFE
  DRA300-B100S-xTx-xxS-GxS  Teflon
  DRA300-B100S-xVx-xxS-GxS  Vespel

 Inlet Pressure
 Ranges

  DRA300-A100S-Hxx-xxS-GxS   3000psi(210bar)
  DRA300-A100S-Lxx-xxS-GxS   600psi(42bar)

 Outlet Pressure
 Ranges

  DRA300-x025x-xxS-xMS-GxS   25psi(1.7bar)
  DRA300-x050x-xxS-xMS-GxS   50psi(3.4bar)
  DRA300-x100x-xxS-xMS-GxS   100psi(7bar)
  DRA300-x250x-xxS-xMS-GxS   250psi(17bar)

 Operating
 Temperature

  PCTFE -40°C ~ +60°C (-40°F ~ +140°F)
  Teflon -40°C ~ +70°C (-40°F ~ +165°F)
  Vespel -40°C ~ +170°C (-40°F ~ +350°F)

 Flow Capacity

  DRA300-x100x-xxS-4MS-GxS   1/4"  Cv=0.06
  DRA300-x100x-xxO-4MS-GxS   1/4"  Cv=0.2
  DRA300-x100x-xxS-8MS-GxS   3/8"  Cv=0.2
  DRA300-x100x-xxS-2MS-GxS   1/2"  Cv=0.5
  DRA300-x100x-xxO-2MS-GxS   1/2"  Cv=1.2
  DRA300-x100x-xxS-3MS-GxS   3/4"  Cv=1.2


    Recommendations


Each product is manufactured taking into consideration of the best safety and easy manipulation. However in order to use the regulator in most safe, effective, precise and smooth way and prolong its life time, you are recommended to use the actual pressure within the range of 25% ~ 75% of its rated pressure.

 


[ Unit conversion program ]

unit unit conversion
atmosphere atm
bar bar
mbar mbar
kg_f/cm^2 kg_f/cm^2
Pound per Squire Inch PSI (= lb/in^2)
dyne per square centimeter dyne/cm^2
Pascal Pa
Newton per square meter N/m^2
Hecto Pascal hPa
Kilo Pascal kPa
Mega Pascal MPa
수주(水柱)밀리미터 mm H_2O (= mm Aq)
수주(水柱)인치 in H_2O (= in Aq)
수은주(水銀柱)밀리미터 mm Hg (= Torr)
수은주(水銀柱)인치 in Hg